[Lab] Zing 24 performance issue

[Ryan Stec]

Its not that radical, and it has been discussed in various ways.

With the Maker Faire a few months away all of our energy is going into
making that event as amazing as we can!

___________________________

Ryan Stec
Artistic Director
Artengine
2 Daly Ave.        Ottawa, ON
K1N 6E2          613.686.1941

Ottawa Maker Faire
November 7th and 8th, 2015
http://makerfaireottawa.com



On Wed, Sep 2, 2015 at 11:55 AM, Darcy Whyte <darcy at inventorartist.com>
wrote:

> This is a bit radical but what about getting a temporary Artengine space
> at Maker Space North?
>
>
>
> --
> Darcy Whyte
>
> Art+ inventorArtist.com <http://inventorartist.com/> | Aviation
> rubber-power.com
> Contact: darcy at inventorArtist.com | 613-563-3634 by appointment (no text)
>
>
> On Wed, Sep 2, 2015 at 11:25 AM, Ryan Stec <ryanstec at artengine.ca> wrote:
>
>> We are going to test it out this week, but due to construction the
>> exhaust to the parking lot is no longer available. All windows on the first
>> floor of the building facing the construction site are boarded up as they
>> are using blasting techniques to excavate. This situation is likely long
>> term, but we don't have specific details about the boarding. The blasting
>> and its accompanying jack hammering is to continue through the fall.
>>
>> We will update if the cable replacement works and also on the conditions
>> of M76.
>>
>> Cheers
>> Ryan
>>
>> ___________________________
>>
>> Ryan Stec
>> Artistic Director
>> Artengine
>> 2 Daly Ave.        Ottawa, ON
>> K1N 6E2          613.686.1941
>>
>> Ottawa Maker Faire
>> November 7th and 8th, 2015
>> http://makerfaireottawa.com
>>
>>
>>
>> On Wed, Sep 2, 2015 at 11:11 AM, Britta Evans-Fenton <
>> brittawater at gmail.com> wrote:
>>
>>> Hey guys,
>>>
>>> I'm pretty sure I solved the problem. I've been talking with the epilog
>>> guys, and there was a miscommunication with Remco on what needed to be
>>> replayed. We got the part shipped in and we are only waiting to rehook up
>>> the laser to a filter system before we can use it again to test it out.
>>>
>>> Assuming Remco still needs help on this, can someone help hook the laser
>>> up to the filter? I know we have changed the filter around, so Doug should
>>> be involved in some way.
>>>
>>> Cheers,
>>>
>>> *Britta Evans-Fenton*
>>> Cultural Producer
>>>
>>> Call for Maker is now OPEN!
>>> *makerfaireottawa.com/ <http://makerfaireottawa.com/>*
>>> Early Bird Deadline: Sept 1st
>>>
>>> On Wed, Sep 2, 2015 at 10:15 AM, Stephen Burke <steve at envirolaser.com>
>>> wrote:
>>>
>>>> The easiest way I can describe the problem is that the Zing 24 doesn't
>>>> "home to origin" properly.  That is to say, if you position the gantry to
>>>> any position that is not the home position when the power is off, and power
>>>> on, the gantry is supposed to move to the rear of the unit with the head at
>>>> the back left corner.  At this point in time, it doesn't do that.
>>>>
>>>> This indicates a problem with the Y axis control, most likely due to a
>>>> sensor malfunction or a sensor cable that is damaged.
>>>>
>>>>
>>>> Stephen Burke
>>>> Account Executive
>>>> Envirolaser Ltd.
>>>>
>>>> 613-619-1013 cell
>>>> 613-225-4726 office
>>>> _______________________________________________
>>>> Lab mailing list
>>>> 1. subscribe http://artengine.ca/mailman/listinfo/lab
>>>> 2. then email Lab at artengine.ca to send your message to the list
>>>>
>>>
>>>
>>> _______________________________________________
>>> Lab mailing list
>>> 1. subscribe http://artengine.ca/mailman/listinfo/lab
>>> 2. then email Lab at artengine.ca to send your message to the list
>>>
>>
>>
>> _______________________________________________
>> Lab mailing list
>> 1. subscribe http://artengine.ca/mailman/listinfo/lab
>> 2. then email Lab at artengine.ca to send your message to the list
>>
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://artengine.ca/pipermail/lab/attachments/20150902/f5f9141b/attachment.html>