[Lab] Zing 24 performance issue

[Darcy Whyte]

This is a bit radical but what about getting a temporary Artengine space at
Maker Space North?



--
Darcy Whyte

Art+ inventorArtist.com <http://inventorartist.com/> | Aviation
rubber-power.com
Contact: darcy at inventorArtist.com | 613-563-3634 by appointment (no text)


On Wed, Sep 2, 2015 at 11:25 AM, Ryan Stec <ryanstec at artengine.ca> wrote:

> We are going to test it out this week, but due to construction the exhaust
> to the parking lot is no longer available. All windows on the first floor
> of the building facing the construction site are boarded up as they are
> using blasting techniques to excavate. This situation is likely long term,
> but we don't have specific details about the boarding. The blasting and its
> accompanying jack hammering is to continue through the fall.
>
> We will update if the cable replacement works and also on the conditions
> of M76.
>
> Cheers
> Ryan
>
> ___________________________
>
> Ryan Stec
> Artistic Director
> Artengine
> 2 Daly Ave.        Ottawa, ON
> K1N 6E2          613.686.1941
>
> Ottawa Maker Faire
> November 7th and 8th, 2015
> http://makerfaireottawa.com
>
>
>
> On Wed, Sep 2, 2015 at 11:11 AM, Britta Evans-Fenton <
> brittawater at gmail.com> wrote:
>
>> Hey guys,
>>
>> I'm pretty sure I solved the problem. I've been talking with the epilog
>> guys, and there was a miscommunication with Remco on what needed to be
>> replayed. We got the part shipped in and we are only waiting to rehook up
>> the laser to a filter system before we can use it again to test it out.
>>
>> Assuming Remco still needs help on this, can someone help hook the laser
>> up to the filter? I know we have changed the filter around, so Doug should
>> be involved in some way.
>>
>> Cheers,
>>
>> *Britta Evans-Fenton*
>> Cultural Producer
>>
>> Call for Maker is now OPEN!
>> *makerfaireottawa.com/ <http://makerfaireottawa.com/>*
>> Early Bird Deadline: Sept 1st
>>
>> On Wed, Sep 2, 2015 at 10:15 AM, Stephen Burke <steve at envirolaser.com>
>> wrote:
>>
>>> The easiest way I can describe the problem is that the Zing 24 doesn't
>>> "home to origin" properly.  That is to say, if you position the gantry to
>>> any position that is not the home position when the power is off, and power
>>> on, the gantry is supposed to move to the rear of the unit with the head at
>>> the back left corner.  At this point in time, it doesn't do that.
>>>
>>> This indicates a problem with the Y axis control, most likely due to a
>>> sensor malfunction or a sensor cable that is damaged.
>>>
>>>
>>> Stephen Burke
>>> Account Executive
>>> Envirolaser Ltd.
>>>
>>> 613-619-1013 cell
>>> 613-225-4726 office
>>> _______________________________________________
>>> Lab mailing list
>>> 1. subscribe http://artengine.ca/mailman/listinfo/lab
>>> 2. then email Lab at artengine.ca to send your message to the list
>>>
>>
>>
>> _______________________________________________
>> Lab mailing list
>> 1. subscribe http://artengine.ca/mailman/listinfo/lab
>> 2. then email Lab at artengine.ca to send your message to the list
>>
>
>
> _______________________________________________
> Lab mailing list
> 1. subscribe http://artengine.ca/mailman/listinfo/lab
> 2. then email Lab at artengine.ca to send your message to the list
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://artengine.ca/pipermail/lab/attachments/20150902/4889474b/attachment.html>