[Lab] Zing 24 performance issue

[Wesley Ellis]

Anyone want to try hooking up the filter tonight?

Wesley Ellis
http://about.tahnok.me

On Wed, Sep 2, 2015 at 12:14 PM, Ryan Stec <ryanstec at artengine.ca> wrote:

> Its not that radical, and it has been discussed in various ways.
>
> With the Maker Faire a few months away all of our energy is going into
> making that event as amazing as we can!
>
> ___________________________
>
> Ryan Stec
> Artistic Director
> Artengine
> 2 Daly Ave.        Ottawa, ON
> K1N 6E2          613.686.1941
>
> Ottawa Maker Faire
> November 7th and 8th, 2015
> http://makerfaireottawa.com
>
>
>
> On Wed, Sep 2, 2015 at 11:55 AM, Darcy Whyte <darcy at inventorartist.com>
> wrote:
>
>> This is a bit radical but what about getting a temporary Artengine space
>> at Maker Space North?
>>
>>
>>
>> --
>> Darcy Whyte
>>
>> Art+ inventorArtist.com <http://inventorartist.com/> | Aviation
>> rubber-power.com
>> Contact: darcy at inventorArtist.com | 613-563-3634 by appointment (no text)
>>
>>
>> On Wed, Sep 2, 2015 at 11:25 AM, Ryan Stec <ryanstec at artengine.ca> wrote:
>>
>>> We are going to test it out this week, but due to construction the
>>> exhaust to the parking lot is no longer available. All windows on the first
>>> floor of the building facing the construction site are boarded up as they
>>> are using blasting techniques to excavate. This situation is likely long
>>> term, but we don't have specific details about the boarding. The blasting
>>> and its accompanying jack hammering is to continue through the fall.
>>>
>>> We will update if the cable replacement works and also on the conditions
>>> of M76.
>>>
>>> Cheers
>>> Ryan
>>>
>>> ___________________________
>>>
>>> Ryan Stec
>>> Artistic Director
>>> Artengine
>>> 2 Daly Ave.        Ottawa, ON
>>> K1N 6E2          613.686.1941
>>>
>>> Ottawa Maker Faire
>>> November 7th and 8th, 2015
>>> http://makerfaireottawa.com
>>>
>>>
>>>
>>> On Wed, Sep 2, 2015 at 11:11 AM, Britta Evans-Fenton <
>>> brittawater at gmail.com> wrote:
>>>
>>>> Hey guys,
>>>>
>>>> I'm pretty sure I solved the problem. I've been talking with the epilog
>>>> guys, and there was a miscommunication with Remco on what needed to be
>>>> replayed. We got the part shipped in and we are only waiting to rehook up
>>>> the laser to a filter system before we can use it again to test it out.
>>>>
>>>> Assuming Remco still needs help on this, can someone help hook the
>>>> laser up to the filter? I know we have changed the filter around, so Doug
>>>> should be involved in some way.
>>>>
>>>> Cheers,
>>>>
>>>> *Britta Evans-Fenton*
>>>> Cultural Producer
>>>>
>>>> Call for Maker is now OPEN!
>>>> *makerfaireottawa.com/ <http://makerfaireottawa.com/>*
>>>> Early Bird Deadline: Sept 1st
>>>>
>>>> On Wed, Sep 2, 2015 at 10:15 AM, Stephen Burke <steve at envirolaser.com>
>>>> wrote:
>>>>
>>>>> The easiest way I can describe the problem is that the Zing 24 doesn't
>>>>> "home to origin" properly.  That is to say, if you position the gantry to
>>>>> any position that is not the home position when the power is off, and power
>>>>> on, the gantry is supposed to move to the rear of the unit with the head at
>>>>> the back left corner.  At this point in time, it doesn't do that.
>>>>>
>>>>> This indicates a problem with the Y axis control, most likely due to a
>>>>> sensor malfunction or a sensor cable that is damaged.
>>>>>
>>>>>
>>>>> Stephen Burke
>>>>> Account Executive
>>>>> Envirolaser Ltd.
>>>>>
>>>>> 613-619-1013 cell
>>>>> 613-225-4726 office
>>>>> _______________________________________________
>>>>> Lab mailing list
>>>>> 1. subscribe http://artengine.ca/mailman/listinfo/lab
>>>>> 2. then email Lab at artengine.ca to send your message to the list
>>>>>
>>>>
>>>>
>>>> _______________________________________________
>>>> Lab mailing list
>>>> 1. subscribe http://artengine.ca/mailman/listinfo/lab
>>>> 2. then email Lab at artengine.ca to send your message to the list
>>>>
>>>
>>>
>>> _______________________________________________
>>> Lab mailing list
>>> 1. subscribe http://artengine.ca/mailman/listinfo/lab
>>> 2. then email Lab at artengine.ca to send your message to the list
>>>
>>
>>
>
> _______________________________________________
> Lab mailing list
> 1. subscribe http://artengine.ca/mailman/listinfo/lab
> 2. then email Lab at artengine.ca to send your message to the list
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://artengine.ca/pipermail/lab/attachments/20150902/ebb99273/attachment-0001.html>