[Lab] cheap laser cutters

[Darcy Whyte]

I'm not sure the wiki is open to enough people to edit it...  I don't see a
link to add a new user and I don't even think my account to edit the wiki
exists any-more. I just tried to log in out of curiosity and it says I
don't have an account any-more.

I don't really think it needs a log (except perhaps a place where the
current status can be updated). All it really needs is some people to take
on the project of maintenance.



--
Darcy Whyte

Art+ inventorArtist.com <http://inventorartist.com/> | Aviation
rubber-power.com
Contact: darcy at inventorArtist.com | 613-563-3634 by appointment (no text)


On Fri, Aug 28, 2015 at 11:55 AM, Henri Kuschkowitz <
henri.kuschkowitz at gmail.com> wrote:

> Ditto what Darcy said.
>
> I used the laser 2-3 weeks ago and the focus was fine. Just the whole
> coordinated issue was still there.
>
> Do we have a reference for all the troubleshooting that has been done up
> tot this point somewhere? Mind you, I am aware of the wiki page with the
> temerity solution.
>
>
> Cheers,
> Henri Kuschkowitz
>
>
>
>
> On Fri, Aug 28, 2015 at 7:58 AM -0700, "Darcy Whyte" <
> darcy at inventorartist.com> wrote:
>
> Don't disassemble... there are a lot of problems because of people taking
>> it apart...
>>
>>
>>
>> --
>> Darcy Whyte
>>
>> Art+ inventorArtist.com <http://inventorartist.com/> | Aviation
>> rubber-power.com
>> Contact: darcy at inventorArtist.com | 613-563-3634 by appointment (no text)
>>
>>
>> On Fri, Aug 28, 2015 at 10:55 AM, Andrew Szeto <andrew.szeto at outlook.com>
>> wrote:
>>
>>> I usually try and clean the optics as best as possible with the q-tips
>>> and solution, but that may just be the tip of the issue i'm guessing.
>>> should we be trying to take the lenses apart?
>>>
>>>
>>>
>>>
>>> ------------------------------
>>> From: darcy at inventorartist.com
>>> Date: Fri, 28 Aug 2015 10:48:59 -0400
>>> Subject: Re: [Lab] cheap laser cutters
>>> To: andrew.szeto at outlook.com
>>> CC: tom.i.burns at gmail.com; lab at artengine.ca
>>>
>>>
>>> Are the optics clean? Are the optics undamaged?
>>>
>>>
>>>
>>>
>>>
>>> --
>>> Darcy Whyte
>>>
>>> Art+ inventorArtist.com <http://inventorartist.com/> | Aviation
>>> rubber-power.com
>>> Contact: darcy at inventorArtist.com | 613-563-3634 by appointment (no
>>> text)
>>>
>>>
>>> On Fri, Aug 28, 2015 at 10:31 AM, Andrew Szeto <andrew.szeto at outlook.com
>>> > wrote:
>>>
>>> Hey Guys!
>>>
>>> Soo maybe a bit late on this one, but anyone know why or have a fix for
>>> the out of focus printing at m76? I was considering those full spectrum
>>> hobby lasers, but they are pretty damn pricey with the exchange rates these
>>> days...
>>>
>>> Thanks!
>>> A
>>>
>>>
>>>
>>>
>>> ------------------------------
>>> From: darcy at inventorartist.com
>>> Date: Tue, 25 Aug 2015 11:16:24 -0400
>>> To: tom.i.burns at gmail.com
>>> CC: lab at artengine.ca
>>> Subject: Re: [Lab] cheap laser cutters
>>>
>>> One thing to consider is the purpose of the purchase. Is it for a
>>> specific project? Is it just for fun?
>>>
>>>
>>>
>>>
>>>
>>> --
>>> Darcy Whyte
>>>
>>> Art+ inventorArtist.com <http://inventorartist.com/> | Aviation
>>> rubber-power.com
>>> Contact: darcy at inventorArtist.com | 613-563-3634 by appointment (no
>>> text)
>>>
>>>
>>> On Mon, Aug 24, 2015 at 3:17 PM, Tom Burns <tom.i.burns at gmail.com>
>>> wrote:
>>>
>>> Hi,
>>>
>>>  Does anyone have experience with these cheap chinese laser cutters?
>>>
>>>
>>> http://www.ebay.com/itm/40W-CO2-USB-Laser-Engraving-Cutting-Machine-Engraver-Cutter-woodworking-Crafts-/121734293301
>>>
>>> Interested in your experience, what you cut, how did it go.  I had no
>>> clue these were available under $500.
>>>
>>> Thanks,
>>> Tom
>>>
>>> _______________________________________________
>>> Lab mailing list
>>> 1. subscribe http://artengine.ca/mailman/listinfo/lab
>>> 2. then email Lab at artengine.ca to send your message to the list
>>>
>>>
>>>
>>> _______________________________________________ Lab mailing list 1.
>>> subscribe http://artengine.ca/mailman/listinfo/lab 2. then email
>>> Lab at artengine.ca to send your message to the list
>>>
>>>
>>>
>>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://artengine.ca/pipermail/lab/attachments/20150828/949dbcef/attachment.html>