[Lab] Laser update

Richard Sloan rsloan at themindfactory.com
Wed Nov 26 14:23:07 EST 2014


Yeah I am not familiar with the bed issue, will look at that maybe tonight,
I am very familiar with the current issue, I have a plan for a test tonight
to further my understanding of it.

On a side note,. where the h*** have you been???? :-)

Richard.


On Wed, Nov 26, 2014 at 1:52 PM, Henri K <henri.kuschkowitz at gmail.com>
wrote:

> Thanks Richard,
>
> all good points. i tried before lowering the bed all the way to the ground
> as well without success. if all fails, shimming it is.
>
>
> Cheers,
> Henri Kuschkowitz
>
> On November 25, 2014 at 11:34:48 PM, Darcy Whyte (darcy at inventorartist.com)
> wrote:
>
> I poked by on my way out to a social this evening and looked at the bed.
> There was some poopie in one of the holes in the fixture. Here's a picture
> of the one right by the exhaust port. I checked bed alignment after that
> and it seemed okay.
>
> Trick is once you focus, move the focus gauge to the corners of your work
> area to make sure you're level enough..If not, shim the work piece or check
> under the tray...
>
> The fixture is badly designed on this machine for this problem...
>
> Oh, there's another thing.. the way it's designed it's easy to put the
> cutting grid on with only the top left feet in the fixture....
>
>
>
>
>  --
> Darcy Whyte
>
> Art+ inventorArtist.com <http://inventorartist.com/> | Aviation
> rubber-power.com
> Contact: darcy at inventorArtist.com | 613-563-3634 by appointment (no text)
>
>
>
>
>
> On Tue, Nov 25, 2014 at 9:40 PM, Richard Sloan <rsloan at themindfactory.com>
> wrote:
>
>> Hope that is it, but my gut feel is that it won't be, I think it's more
>> the end stop sensor, unless it's a bad input on the controller for that end
>> stop... just does not feel like a controller issue.  Hope manufacturer is
>> right, one hell of a price to pay if they are wrong.
>>
>> Richard.
>>  On 2014-11-25 10:40 AM, "Remco Volmer" <programming at artengine.ca> wrote:
>>
>>> Hi all,
>>>
>>> After lengthy conversations with the manufacturer, the current
>>> solution is to replace the entire controller pad. A new one has been
>>> ordered and should arrive this week. Thank you for your patience.
>>>
>>> Remco
>>>
>>> _______________________________________________
>>> Lab mailing list
>>> 1. subscribe http://artengine.ca/mailman/listinfo/lab
>>> 2. then email Lab at artengine.ca to send your message to the list
>>>
>>
>> _______________________________________________
>> Lab mailing list
>> 1. subscribe http://artengine.ca/mailman/listinfo/lab
>> 2. then email Lab at artengine.ca to send your message to the list
>>
>
>  ------------------------------
> _______________________________________________
> Lab mailing list
> 1. subscribe http://artengine.ca/mailman/listinfo/lab
> 2. then email Lab at artengine.ca to send your message to the list
>
>
> _______________________________________________
> Lab mailing list
> 1. subscribe http://artengine.ca/mailman/listinfo/lab
> 2. then email Lab at artengine.ca to send your message to the list
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://artengine.ca/pipermail/lab/attachments/20141126/5cfd9ff1/attachment.html>


More information about the Lab mailing list