<p dir="ltr">Hey Wes, the short story is the print didn't go... yet. We had a pile of technical difficulties. That said, the attached file should print and the colours have been fixed to proper red and black values. If it works for you, let us know!</p>
<div class="gmail_quote">Le 2014-08-23 18:45, <<a href="mailto:rsloan@themindfactory.com">rsloan@themindfactory.com</a>> a écrit :<br type="attribution"><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
As for the files, I am sure Arnold can give em up :-)<br>
<br>
R.<br>
<br>
Quoting Wesley Ellis <<a href="mailto:tahnok@gmail.com" target="_blank">tahnok@gmail.com</a>>:<br>
<br>
<blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
How did these cuts go? Can you post the files publicly?<br>
<br>
On Wed Aug 20 16:02:20 2014, Richard Sloan wrote:<br>
<blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
I have sent files to Jason to bring tonight that are more laser<br>
friendly....<br>
<br>
There are 2 colors for the 0.001" lines, an almost black and almost<br>
red, I have noted the exact colors and we can setup the laser to "see"<br>
these.... the black is a vector cut all the way through the cardboard,<br>
and the red can also be a vector, but it does not cut all the way, it<br>
allows for a hinge (fold), if we find the hinge slot to be too small<br>
we can widen it tonight and cut out a slightly wider cut to allow for<br>
more hinge movement.<br>
<br>
R.<br>
<br>
<br>
<br>
On Wed, Aug 20, 2014 at 3:58 PM, Richard Sloan<br>
<<a href="mailto:rsloan@themindfactory.com" target="_blank">rsloan@themindfactory.com</a> <mailto:<a href="mailto:rsloan@themindfactory.com" target="_blank">rsloan@themindfactory.<u></u>com</a>>> wrote:<br>
<br>
I have sent the files to Jason to bring tonight, I made it more<br>
laser ready.....<br>
<br>
<br>
On Wed, Aug 20, 2014 at 3:16 PM, Richard Sloan<br>
<<a href="mailto:rsloan@themindfactory.com" target="_blank">rsloan@themindfactory.com</a> <mailto:<a href="mailto:rsloan@themindfactory.com" target="_blank">rsloan@themindfactory.<u></u>com</a>>> wrote:<br>
<br>
I am sure one of us can look at it :-) you can send it to me<br>
now and I can see what its like.....<br>
<br>
<br>
On Wed, Aug 20, 2014 at 3:11 PM, Jason Arnold<br>
<<a href="mailto:arnold.jason@gmail.com" target="_blank">arnold.jason@gmail.com</a> <mailto:<a href="mailto:arnold.jason@gmail.com" target="_blank">arnold.jason@gmail.com</a><u></u>>> wrote:<br>
<br>
I've seen a few people post about this, but don't know if<br>
ever got off the ground.<br>
<br>
I've got the .eps files, but I was sick on the night of<br>
Britta's last workshop and don't know all the intermediate<br>
steps to make it into a laser-friendly PDF :(<br>
<br>
Hoping someone can spare a few at ModLab tonight?<br>
<br>
*Jason*<br>
<br>
______________________________<u></u>_________________<br>
Lab mailing list<br>
1. subscribe <a href="http://artengine.ca/mailman/listinfo/lab" target="_blank">http://artengine.ca/mailman/<u></u>listinfo/lab</a><br>
2. then email <a href="mailto:Lab@artengine.ca" target="_blank">Lab@artengine.ca</a> <mailto:<a href="mailto:Lab@artengine.ca" target="_blank">Lab@artengine.ca</a>><br>
to send your message to the list<br>
<br>
<br>
<br>
<br>
<br>
<br>
______________________________<u></u>_________________<br>
Lab mailing list<br>
1. subscribe <a href="http://artengine.ca/mailman/listinfo/lab" target="_blank">http://artengine.ca/mailman/<u></u>listinfo/lab</a><br>
2. then email <a href="mailto:Lab@artengine.ca" target="_blank">Lab@artengine.ca</a> to send your message to the list<br>
</blockquote>
<br>
</blockquote>
<br>
<br>
</blockquote></div>